FasLink X Remote Key Fob Programmer for GM keyless Entry Programmer Remote Transponder Key Fob w/Auto Programming Tool OBD2 Connector. 4.0 out of 5 stars 23. Join Prime to save $16.96 on this item. Get it as soon as Mon, Jan 18. FREE Shipping by Amazon. Only 20 left in stock. You can program or reprogram your keyless-entry FOB system in just minutes from your vehicle. Programming requires only your ignition key and your keyless remote itself and you will be ready to use the device immediately with your car, truck or SUV. Dodge Key Fob Programming Guide. If you've replaced the battery and checked the connections in your key fob but your car still isn't responding, you may need to reprogram the key fob. To reprogram your Dodge key fob, follow the four easy steps below. These steps will also work on select Chrysler, Jeep, and RAM models in Bartlett and Streamwood.
Download Instructions
Hood Pin Equipped Vehicles
- Press and hold the hood-pin for 4 seconds
What is a hood-pin? - Release the hood-pin (the parking lights will turn on)
What are parking lights? - While the parking lights are on, press the hood-pin once more and release immediately
- The parking lights will now stay on for up to 20 seconds
- Before the parking lights go out, turn the ignition key ON (RUN Position) and immediately to the OFF position
- Press and HOLD the LOCK button of the key fob you are trying to program and keep it held down until the parking lights flash 5 times quickly (may be followed by 2 slow flashes, not all the time though)
- The key fob has now been stored to memory
If you have additional key fobs to program, repeat step 5 and 6 at this time. *Systems can hold a maximum of 4 remotes
Here is a YouTube video we have made to assist with programming:
NO HOOD PIN? How To Program
Option 1: (if the antenna on your windshield HAS an Antenna Programming Assistance Button (A.P.A.B.)
- Make sure the hood is closed
- Turn the ignition key to the IGNITION ON (RUN) position
- Within 5 seconds, press the programming button on the antenna twice for 1 second each time. THE LED WILL COME ON SOLID.
- You now have 20 seconds to select one of the sub-menus (proceed with transmitter programming procedure below:
Note: To exit programming mode, press on the antenna button once (the LED will come ON) and release.
Transmitter Programming Programming Procedure
- Before the lights go out, turn the ignition key to the Ignition Off position, then to On (Run) position and immediately to the OFF position. OFF/ON/OFF
- Press and hold the LOCK button and keep it down until the parking lights flash 5 times quickly. The transmitter has been stored to memory AFTER the 5 flashes, meaning programming is completed.
You must repeat the above process to add additional transmitters.
Option 2: (If the A.P.A.B. button is not present on the antenna)
Here is a YouTube video we have made to assist with programming if your vehicle does NOT have a hood pin:
Wondering what a hood pin is, or where it is located?
Need to purchase a hood pin?
This post show a guide on how to use OPCOM -VAXU-COM program injectors Opel.
Preparations:
- Omega-B
Y25DT
There is no need to manually enter the injector codes on these.
You need to execute the ”'[Injectrs were replaced]”’ diagnostic procedure from the menu to code the replaced injectors.
- Astra-G
Z17DLT
There is no need to manually enter the injector codes on these.
- Astra-H / Zafira-B
Z17DTH/Z17DTL
On these, you do not need to enter the quantity adjustment codes, for each injector.
All you need to do, is to choose, which injector was replaced.
Available options are 1, 2, 3, 4, or all.
Z19DT/Z19DTH/Z19DTL/Z19DTJ
The procedure is the same, as the Vectra-C / Signum
- Vectra-C / Signum
Z19DT/Z19DTH/Z19DTL/Z19DTJ
The injector code, which contains 9 letters is written on the injector itself.
When you replace these injectors, the engine control unit must be coded, to ensure the proper operation of these EDC16 injectors.
The injector code consist of 9 letters, using the following character table:
A,B,C,D,E,F,G,H,I,K,L,M,N,O,P,R,S,T,U,V,W,X,Y,Z,1,2,3,4,5,6,7,8
An example injector code: 81SPBF7AA
1
- Corsa-C / Meriva
Z17DTH
The injector code, which contains 22 letters (11 hexadecimal numbers) is written on the injector itself.
When you replace these injectors, the engine control unit must be coded, to ensure the proper operation of these DEC30 injectors.
The injector code consist of 22 letters, using the following character table:0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F
An example injector code: D500CA0000BECEEBD7CDCE
2
3
Z13DTH
The injector code, which contains 9 letters is written on the injector itself.
When you replace these injectors, the engine control unit must be coded, to ensure the proper operation of these MultiJET injectors.
The injector code consist of 9 letters, using the following character table:
A,B,C,D,E,F,G,H,I,K,L,M,N,O,P,R,S,T,U,V,W,X,Y,Z,1,2,3,4,5,6,7,8
An example injector code: BKAPM2EC8
When a MultiJET engine ECU is opened for diagnostic, the following window will appear:
4
Click on the [Programming] button, to read-out the stored injector codes.
5
Opcom Key Fob Programming Tutorial
Please ensure, that Ignition is ON, and engine is NOT running.
Opcom Key Fob Programming Entry
On this window, you’ll see the current injector quantity adjustment codes, for each cylinder.
Please only change one adjustment code at once, then click on the corresponding [Change] button.
Corsa C Key Fob Programming Opcom
The result of the programming will be displayed correctly. After programming, cycle igniton,and then read out the stored injector codes again, to verify the programming process.